Beko National Sales is an authorized Beko Technologies distributor with access to the complete product catalog — filtration, drying, condensate drains, and oil-water separation. Clean, dry, and reliable compressed air from generation to point-of-use, spec'd correctly for your process.
Tell us about your application and we will follow up with a product recommendation and pricing.
For industrial and manufacturing facilities only. We will never share your information.
As an authorized Beko Technologies distributor, we can source any product in the Beko catalog. Below are the core system components most industrial facilities require — filtration, drying, condensate draining, and oil-water separation. We help you select, size, and integrate the right solution for your process.
DRYPOINT® X desiccant dryers deliver pressure dewpoints as low as -100°F (-73°C) for critical processes where even trace moisture cannot be tolerated. Available in heatless, heated, and blower-purge configurations across a wide flow range.
DRYPOINT® RA and RX refrigerated dryers deliver a stable pressure dewpoint of +37°F (+3°C) for reliable protection of pneumatic equipment, tooling, and general plant air systems. Energy-saving cycling models match power consumption to actual demand.
CLEARPOINT® filters remove particles, aerosols, and oil vapor from compressed air with industry-leading energy efficiency. Coalescing, particulate, and activated carbon filter elements cover every ISO 8573-1 air quality class from bulk liquid removal to oil vapor elimination.
BEKOMAT® intelligent zero air loss drains eliminate the compressed air waste of timed blow-down drains. QWIK-PURE® oil-water separators treat the collected condensate to EPA-compliant discharge levels — separating dispersed and emulsified oil before disposal.
Compressed air leaving a compressor is hot, wet, contaminated with oil aerosols, and loaded with particulate. Without proper filtration, drying, and condensate management, those contaminants reach your tools, your product, and your process. The cost of a contamination event — downtime, failed audits, scrapped product, regulatory exposure — almost always exceeds the cost of the treatment system that prevents it.
Liquid water, rust particles, and compressor wear debris in untreated compressed air corrode pipework, destroy pneumatic actuators, contaminate food and pharmaceutical product, and cause premature equipment failure. ISO 8573-1 defines the air quality classes your process must meet — most facilities are not meeting them without proper filtration and drying in place.
Every oil-lubricated compressor introduces oil aerosols and vapor into the air stream. Without coalescing and activated carbon filtration, that oil reaches product contact surfaces, fails SQF, HACCP, and GMP audits, and creates condensate disposal liability. CLEARPOINT® filtration reduces oil carryover to as low as 0.005 mg/m³ — meeting the most stringent air quality requirements.
A dryer sized for average flow demand fails during peak production. A refrigerated dryer in a below-freezing equipment room ices up and bypasses. A heatless desiccant dryer with excessive purge rate starves downstream demand. Compressed air treatment is a system — and every component must be selected and sized for your actual operating conditions, not catalog defaults.
Beko National Sales specializes in complete compressed air treatment system specification. We evaluate your full system — from the compressor outlet to the point-of-use — and recommend the right combination of filtration, drying, condensate management, and oil-water separation. With access to the full Beko Technologies catalog, we match every component to your actual process requirements, flow conditions, and compliance obligations.
Most distributors pull a catalog number off your flow rate and call it done. That works until your ambient temperature, actual peak demand, process dewpoint requirement, or ISO air quality class makes the default answer the wrong answer — and you find out during production.
Beko National Sales takes a system-level approach. Compressed air treatment is not a single product — it is a coordinated sequence of filtration, drying, condensate drainage, and separation. We evaluate your full system before we recommend any component. With access to the complete Beko Technologies catalog, we are not limited to a short list — we find the right product for your application, regardless of where it sits in the lineup.
Flow rate, operating pressure, required ISO 8573-1 air quality class, ambient conditions, duty cycle, compressed air demand profile, and any process-specific compliance requirements — food, pharmaceutical, environmental.
We identify the correct Beko products across filtration, drying, condensate drainage, and oil-water separation — configured and sized for your actual operating conditions, not catalog defaults.
Specific Beko products, competitive pricing on every component, and a clear technical explanation of how the system addresses your process requirements. You make an informed purchasing decision.
Food contact air typically requires ISO 8573-1 Class 1 or 2 — meaning particle filtration to 0.1 µm, pressure dewpoint below -4°F (-20°C), and oil content below 0.01 mg/m³. A properly specified CLEARPOINT® and DRYPOINT® X system meets these requirements with documentation for HACCP, SQF, and BRC audits.
GMP-compliant compressed air requires validated, documented air quality across all ISO 8573-1 parameters — particulate, humidity, and oil. Beko DRYPOINT® X desiccant dryers and CLEARPOINT® filtration deliver Class 1 air quality with the documentation necessary to support validation and regulatory inspection.
A DRYPOINT® RA refrigerated dryer holding +37°F (+3°C) dewpoint eliminates liquid water from pneumatic circuits, extends tool and actuator service life, and reduces unplanned maintenance. BEKOMAT® zero air loss drains eliminate the continuous air bleed of timed drains — recovering compressor capacity and reducing energy cost.
BEKOMAT® level-controlled drains collect condensate without wasting compressed air. QWIK-PURE® oil-water separators then treat that condensate — separating dispersed and emulsified oil to below 15 ppm for compliant discharge. Required for any oil-lubricated compressor system in a permitted facility.
The full Beko Technologies catalog covers the complete product portfolio — filtration, drying, condensate drainage, oil-water separation, controls, and accessories. Specifications, performance data, sizing guides, and configuration options for every product in the lineup.
Enter your email and we will send you the complete Beko Technologies product catalog immediately.
We will send the catalog to your email. Your information is never shared.
Beko National Sales is an authorized Beko Technologies distributor and an SP Industrial brand. You get access to the complete Beko product portfolio — every model, every configuration — backed by hands-on technical specification and the responsive, family-owned service model of SP Industrial.
Beko Technologies has spent more than four decades developing compressed air filtration, drying, condensate management, and separation systems trusted by industrial facilities worldwide. The portfolio spans ISO 8573-1 Class 1 through Class 5 air quality requirements across a wide range of flow rates, pressures, and operating environments.
We evaluate your full compressed air treatment system — from the compressor outlet to point-of-use — before recommending any product. Required ISO air quality class, ambient conditions, peak flow demand, dewpoint requirement, and compliance obligations all factor into the specification. The right system is not always the obvious one.
Beko CLEARPOINT® and DRYPOINT® systems achieve ISO 8573-1 Class 1 air quality for food and pharmaceutical compliance. QWIK-PURE® separators meet EPA condensate discharge requirements. We provide supporting documentation for SQF, HACCP, BRC, GMP, and environmental permit audits.
As an authorized Beko distributor, we can source any product in the Beko Technologies catalog — not a curated short list. Our quotes are specific: product model, configuration, and price. No ranges, no placeholders. You know exactly what you are getting and what it costs before you commit.
Beko National Sales is backed by SP Industrial — a family-owned business that picks up the phone. When you have a question about a product, an installation, or a replacement part, you reach a person who knows your account.
Desiccant media, CLEARPOINT® filter elements, BEKOMAT® spare parts, and QWIK-PURE® media — we supply the consumables and replacement components your system requires to maintain specification. One source for the equipment and everything it needs to keep performing.
Fill out the form and we will follow up with a complete compressed air treatment recommendation — the right Beko products, correctly specified, with competitive pricing for your application.
Prefer to talk it through first?
360-579-2646 Monday–Friday, 8am–5pm PacificFor industrial and manufacturing facilities. We will review your application and respond with a recommendation and pricing.
We will never share your information. This form is for industrial facility inquiries only.
Whether your facility needs ISO Class 1 food-grade air, low-dewpoint instrument air, general plant air drying, or EPA-compliant condensate management — Beko National Sales has the system and the expertise to get it right.
The best customer service guaranteed · No commitment required · Nationwide service